Alinking ALS-7721 Manual de instrucciones

1 Version 2.3 Date: 2010.03.29 Firmware Version: 1.00

10 LINE OUT Connect a audio devices (e.g. speaker) to the “LINE OUT” socket. NOTE： Two-Way Audio communication must be completed the MI

100 External Alarm I/O Circuit Diagram Attention: Where connecting of a low or high current loop to the external alarm input/output of the p

101 Appendix C: Change the Internet Explorer Settings Change the security setting of IE browser to allow the ActiveX Control be plug-in to the IE bro

102 Appendix D: Set up the Router setting with the video server You can use DHCP when you want to use the camera on the Intranet (LAN). However, the I

103 Appendix E: DDNS Application How to apply and setup the DDNS service? The DDNS (Dynamic DNS) is the network application service. The DDNS can h

104 1. Please enter the website address of “DynDNS” (http://www.dyndns.com/) through Browser. 2. Please click Create Account button. (If you al

105 4. After click “Create Account” button, a confirmation letter will be sent to your mailbox. Please acknowledge the confirmation letter by

106 6. Please click “Dynamic DNS” icon then select ”Dynamic DNS Free” service. 7. Click Get Started button to add the new Hostname. 8.

107 9. After add new hostname, click Next>> to enter the next step. (Note: as you are using “Dynamic DNS Free” service; so you can ignore the

108 How to check if the DDNS service is successful? 1. If you can not connect the IP devices through the domain name, which you have set up, you can

109 Appendix F: Mobile Application Our Video server can support the 3GPP(RTSP) connection through the mobile phone. Please check your ISP to provide t

11 LAN Socket Provide the Ethernet 10/100 base network speed, and insert the LAN cable in the LAN socket. USB This USB interface can support all US

110 Step3: Check the RTSP streaming setting H.264 Type Click “Video/Image“ of Basic Setting  “Video“  Set up the sub streaming resolution (e.g. Plea

111 Step4: View limit Setting According to the requirement, you can pass the live view limit. Please see the illustration as below.

112 Step5: Try to connect Video server through the mobile phone Check the mobile phone can support the streaming media player and internet service, an

113 5. Enter the IP address of the camera e.g. (Without Password) rtsp://xxx.xxx.xxx.xxx:554/cam1/h264-2 e.g. (With Password) rtsp://xxx.xxx.xxx.

114 9. Connecting. 10. Loading the image 12. Show the video stream on the mobile screen. NOTE： If the sof

115 iPhone System Example: iPhone 3GS. Follow these steps to set up the viewing function 1. Download and install the free video streaming soft

116 5. Tap FREE button to change the selection. 6. Tap INSTALL to install the software. 7. Go back the main s

117 8. Tap “Bookmarks” icon 9. Tap “+” signal to add the bookmark. 10. Input your URI link of the video server (e.g. rts

118 11. Tap the link to connect to the video server 12. Show the video stream on the mobile screen 13. Tap the screen to di

119 Appendix G: Support the Cellular / Mobile Phone List Please suggest the list to buy the applicable cellular / Mobile Phone which to use. Brand T

12 Hardware Installation You can install the product on your desk or use the attached tripod to hang it from the wall or ceiling. (The product is prov

120 Appendix H: Multicast Application The Multicast function is a technique for one-to-many communication over an IP infrastructure in a network. T

121 N.O. Item Illustration Note 1 H264 (Main) Display the multicast setting of H264 (Main) 2 H264 (Sub) Display the multicast setting of H

122 H264 (Main) The function has some limit parameter, so please follow our limit parameter to set up it. All restrictions exist in the rear of each

123 H264 (Sub) The setting is the same with the H264 (Sub). NOTE： Suggest using the default parameter to use the multicast function. Please make

124 Motion JPEG The setting is the same with the MJPEG. NOTE： Suggest using the default parameter to use the multicast function. Please make ref

125 Please see the detailed steps to Set up the Multicast function as below: 1. First, check the LAN environment has the device of IGMP service.

126 6. Click On button from Enable Selection to enable the Multicast function. 7. Go back the Live View Mode then click the pull-dow

127 Appendix I: Troubleshooting and FAQs Question Answer and Solution Function What encoder and decoder are used by the camera for sounds and images?

128 IP Finder cannot store network parameters. • Do not use spaces. Use underline “_” or dash “-“. • Your connection might have problems. Please

129 • Check the router and make sure that its setting allows it to access your camera from the Internet. The number of frames transmitted are less th

13 3. Connect to the LAN cable Plug one end of your LAN cable in the LAN socket on the back of the product and connect the other end to the network th

14 Bracket Installation The product can be fixed on the wall (Fig. 1) or hung from the ceiling (Fig. 2). When using the attached bracket and screws

15 Camera Setting After the hardware has been installed, insert the attached CD in the computer and execute “IP Finder.exe” following the steps below

16 4. Submit data (Submit) Click Submit to validate new settings. 5. Confirmation When all changes have been confirmed, click Exit to quit. N

17 Enter the Main Page Open the web browser to login ALS-7721, please see the step by step illustration below: NOTE： If the web browser cannot be di

18 Camera Main Page N.O. Item Illustration Note 1 Logo Display the company logo 2 Product Name Display the product name 3 Language

19 Logo Display the company’s logo of ALINKING then built-in the company’s web link. Click the logo to link our company’s web page.

2 FCC Class A Verification This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This dev

20 Video Socure Select the video source to change the live view mode: Signal Channel (Video 01~02) and Dual Channel (Video 1+2). Signal Channel: Disp

21 Video Format ALS-7721 can provide the triplex streaming for customer application, but the live view can only select one streaming to use. The de

22 Streaming There are 3 kinds of different streaming protocols including UDP, TCP, and HTTP. Set up the streaming protocol to apply or integrate on

23 Color Adjust the color setting of live image by Brightness, Hue, Contrast and Saturation. Select the item then click the + / - button to adjust

24 Alert When the event is triggered, the Alert light will change to red flash to warn the User immediately. The smart design can avoid the user los

25 Feature Column According to the different setting, the Feature Column will display the different application function including Alert Message and P

26 Disable The function can hide the event message to display into Alert Message Text when the event is triggered. If the Alert Message Text had to r

27 Clear Click Clear button to remove all event message from the Alert Message Text. Alert Snapsh

28 Control Panel Control Panel will appear after enable the PTZ function. It provides the some control and application functions. Please see the det

29 Camera Direction Controls the direction of the camera (up, down, left, right, home position). PT

3 Content Content ...

30 ZOOM Click In or Out button to enable the optical ZOOM IN/OUT function. The ZOOM distance will follow the source device, and select the speed fr

31 Preset: Preset the rotation points for the camera (16 points) 5. Select the number you need and click Go. The camera moves to the area auto

32 Tour Enable/disable the tour mode of the camera. The rotation points of the camera must be set up in advance, and ALS-7721 provide five tour add

33 Shortcuts Click the right-button of mouse from Live View to display the Shortcuts List. According to the requirement, select the application funct

34 Original Size No matter what the multiple of digital zoom, select the function to reset the original size. Click the button to enable this functi

35 Record Select the function to record the image of ALS-7721 that saves to default path. Select record again to stop recording. When the function

36 Shortcut Bar Enable/Disable the application function from Shortcut Bar. N.O. Item Illustration Note 1 Microphone Enable/Disable the m

37 Buzzer The function can receive the voice of ALS-7721’s microphone or line in devices. Click the button to enable/disable the buzzer function wh

38 Path The function includes the setting: Path, Filename Prefix and recording limit, please see the detail as below: NOTE： Due to the path setting

39 Record Limit The function only supports the “Record Path Setting” then limit the record file size. ALS-7721 will follow the setting to create th

4 Focus...

40 Shortcut Bar Message The function will display the information of record and snapshot for customer, please see the all status illustration as bel

41 System setting System setting contains basic and application settings. The basic setting is executed for basic system information, transmission sp

42 Basic Setting Basic Setting > System Basic Setting > System > System  Basic Setting > System > System > System Info Device

43 Basic Setting > System > System Log This function can send log file to syslog server to monitor the situation of ALS-7721. You can download f

44 Basic Setting > Video/Image Basic Setting > Video / Image > Video ALS-7721 can provide three video simultaneous stream: H.264 (Main), H.26

45  Basic Setting > Video / Image > Video Image > Resolution Generally speaking, selection of resolution is dependent on the bandwidth of t

46  Basic Setting > Video / Image > Video Image > Quality There are two video quality modes: Fixed rate mode is suitable for use in a netw

47  Basic Setting > Video / Image > Video Image > GOP GOP provides users with the function to set the pages of the I Frame and P Frame to b

48 Basic Setting > Video / Image > PreProc / Overlay  Basic Setting > Video / Image > PreProc > Video Video Source: You can select

49 Basic Setting > Audio  Basic Setting > Audio > Device Audio Setting > Audio There are five kinds of the audio mode to user: Full dupl

5 Application Setting > Blind Detection ...90 Applica

50 Basic Setting > User The administration of the camera can set up access privileges by administrator, operator, and viewer to ensure the security

51  Basic Setting > User > User Setting > User List Click Add (to add a new user), Update (to change the privilege or password of a user o

52  Basic Setting > User > User Setting > User Setting anonymous login: For special business situations, this product allows you to log in t

53 Basic Setting > Network Basic Setting > Network > Network (Wired Network Setting)  Basic Setting > Network > Network > IP Ass

54 Basic Setting > Network > Service  Basic Setting > Network > Service > FTP Service ALS-7721 can become the small FTP server to dow

55 Basic Setting > Network > Streaming Setting of the video streaming port (HTTP and factory default are recommended)  Basic Setting > Net

56 Basic Setting > Network > PPPoE (Dial-up Networking Setting) Point-to-Point Protocol over Ethernet is a protocol that supports access to a hi

57  Basic Setting > Network > PPPoE > PPPoE Dial: You can select whether or not to dial when you boot the machine (On Boot or Off). Userna

58 Basic Setting > Network > DDNS (Dynamic Domain Name Server) The IP address (Ex. 210.168.0.22) is like a telephone number, while the website

59 Basic Setting > Network > UPnP (Universal Plug and Play) If you connect your camera to a router, IP allocator, or wireless AP, your camera wi

6 Introduction ALS-7721 is a multi-functional 2CH H.264 Video Server. Unlike traditional video server, ALS-7721 has a built-in high power CPU and H.2

60 To activate the UPnP function in Windows OS: Ex: Windows XP: 1. Windows component installation. 2. Open Windows firewall option Step 1: Clic

61 3. View the connection device using “My Network Place” 1. Open “My Network Place” Step 2: The LAN camera appears. Double-click to access the

62 Basic Setting > Network > SMTP Server (mail server setting) This camera is able to transmit images to a particular email address when a motio

63 Basic Setting > Network > Samba This camera is able to upload the snapshots to a specified shared folder when an event is triggered. To use t

64 Basic Setting > Network > Notification of IP address Change For a dynamic IP, you need to update the IP address every time you connect to the

65 Basic Setting > Network > Multicast This function allows multiple people to watch video streaming without limitation on the number of users,

66 Basic Setting > Date/Time  Basic Setting > Date/Time > Server Time (the date/time of the server)  Basic Setting > Date/Time >

67 Basic Setting > IP Filter This function filters IP addresses and is able to allow or deny visits from particular addresses/target addresses.

68 Basic Setting > Storage This function can know the Storage information and format it.  Basic Setting > Storage > SD Name: Device

69 Application Setting Application Setting > Event This camera is equipped with intelligent security management functions. It ensures security moni

7 Packaging Contents ALS-7721 is provided with the following accessories. Please contact your dealer if any one of the following is missing. 1. A

70  General: Name: Name the trigger event here, and input the length must from 1 to 24.  Response to event trigger: the time setting of t

71  Response process: trigger event response (Note: Multiple selections are available) Active alarm out: An event is detected by the security equ

72 Upload video/image to server : The IP camera will save the MJPEG/H264 picture or video of the event to the Upload Server (FTP/SMTP) or the Record

73 Base file name (Name): Select the recording type: Picture (.jpg) or Image (.avi) then set the recording file name. The default value is the img

74 Upload Server Type : There are two upload server selections: FTP and SMTP (Mail). FTP: Refer the chapter: Application Setting > Event > Eve

75 Record the image (.AVI) Include pre-trigger buffer: When an event is detected, the camera will record the previous video image up to 10 seconds.

76 Capture the picture (.JPG) Snapshot time offset: (ms) The function is the time setting of previous/post snapshot. The valid range is from -10000

77 For example, the “Snapshot time offset” parameter was used the “+“. The ”+” parameter means post capture the image. Type Capture FTP 1 Pic

78 Send HTTP notification: The alarm will be sent to the HTTP server you specified. To use this function, set the coordinative HTTP server in the

79 Application Setting > Event > Trigger (Manual test the response) Whenever the camera detects abnormal events during the scheduled time, it wi

8 System Instructions Wiring of the product N.O. Item Illustration Note 1 LED Power LED 2 VIDEO IN 2 x BNC Video Input Connection

80  Application Setting > Trigger > Alarm Input Setting Change the alarm input type: N.O.(Normal Open) or N.G. (Normal Ground). The N.G. me

81 Application Setting > Event > Event Servers (Upload Server) Here you can perform a complete setting for uploading files to the server. Please

82  Application Setting > Event > Event Server > Event Server List Add Ftp Enter the information of the FTP server you specified. N

83 Add Http Enter the information of the HTTP server you specified. Name: HTTP name Network Address: HTTP IP address Login: Log-in na

84 Add TCP Enter the information of the TCP server you specified. Name: TCP server name Network Address: TCP IP address Port: TCP p

85 Modify Modifies the setting value Delete Removes the setting value Modify Remove

86 Application Setting > Recording List The function can provide the smart search method to find the SD Card / External HDD recording image easily

87 Video Source: According to the video server type, select the Video 1, Video 2 or Both Video to search the recording image. Trigger: There are se

88  Application Setting > Recording List > Recording List Display the result to recording list after click Search button. Download: Select th

89 Application Setting > Motion Detection Open the setting frame by clicking on the area to monitor. To move area to monitor, drag the area with yo

9 LED The camera uses a high-luminance red LED to display the power information. VIDEO IN Plug the video source into the Video input to get the i

90 Application Setting > Blind Detection The bland detection means the inside/outside area detection. When the inside/outside object can be move

91 Application Setting > Privacy Maskv The privacy zone function can mask the image in the mask zone to ensure confidentiality. First, select a mas

92 Application Setting > Firmware upgrade Contact your dealer for more information about firmware upgrade. Please follow the steps below to execu

93 5. The auto upgrade runs. The Upgrade Status shows the progress of the upgrade. 6. When the firmware upgrade has been completed, the machine r

94 Application Setting > Factory Default You can use this function to reset to factory default, but all changes, including the IP address, you have

95  Application Setting > Factory Default > Backup Back all parameters: Back up all changes you have made. When you click Backup, a file down

96 Application Setting > Reboot Enable this function for the camera to reboot automatically. Reboot the Video Server

97 Appendix A: System Requirements Before installing ALS-7721, please make sure your system has the following recommended minimum hardware requirement

98 Appendix B: External Alarm & RS485 In addition to the motion detection executed by the internal software application, the product can connect t

99 ALARM INPUT： The extra device connects one for the Alarm Input (A), and the other for Alarm Input (K). Due to ALS-7721 has the protection mechanis